General Questions (41)

No Registration Required To Ask & Answer Questions! Features Such As Voting or Marking Favorites Cannot Be Accessed Without Registration! All Questions & Answers Are Subject To A Small Delay In Posting Due To Moderation!
Votes
Answers
Views
Question
0
votes
0
answers
10
views
Be first to answer!
Asked 10 months ago By Anonymous User
Category: General Questions
0
votes
0
answers
17
views
Be first to answer!
Asked 10 months ago By GMan
Category: General Questions
Hoping you could tell me how to determine air flow in a concentric system.  Anything on this?
0
votes
0
answers
9
views
Be first to answer!
Asked 10 months ago By jayakarthick
Category: General Questions
Unmistakably, this territory is involved with various sorts of windings. For example, sectional and trapezoidal winding, layer quits, spreading, taking away and beginning with the tweaked methodology are open. The CNC control can make certain working...
0
votes
0
answers
12
views
Be first to answer!
Asked 10 months ago By Hot and Cold
Category: General Questions
I have a split level house. Three bedrooms are on the upper floor; the furnace is in the basement on the opposite end of the house. A dedicated supply duct comes off the furnace, across the house and up to the second floor.  There it forks off to the...
0
votes
0
answers
14
views
Be first to answer!
Asked 10 months ago By Ed Kirk
Category: General Questions
Hello I am the instructor for the HVAC program at Palomar College.  We are in the process of starting a new HVAC program and I am looking for a source to design and fabricate some equipment for our program.  I was at the College of the Desert in Palm...
0
votes
0
answers
4
views
Be first to answer!
Asked 10 months ago By Mike
Category: General Questions
0
votes
0
answers
47
views
Be first to answer!
Asked 10 months ago By Anonymous User
Category: General Questions
0
votes
0
answers
7
views
Be first to answer!
Asked 10 months ago By Dennis
Category: General Questions
In a typical 1/2 horsepower centrifugal fan, I've been told that if the static pressure is too low, the amperage draw goes up and the airflow goes down.  Is there a minimum recommended static pressure for a centrifugal fan?
0
votes
0
answers
4
views
Be first to answer!
Asked 10 months ago By Sean
Category: General Questions
0
votes
0
answers
26
views
Be first to answer!
Asked 10 months ago By Jim
Category: General Questions
Have a speedair 3 cyl.progressive air compressor,have access to and want to use  a dayton 3hp single phase farm moter,,,,,yes or no???
0
votes
0
answers
27
views
Be first to answer!
Asked 10 months ago By Anonymous User
Category: General Questions
The difference between industrial and commercial grade fans construction is the following: Industrial equipment is specifically designed and built to stand up to the rigors of an industrial application. The differences are concrete and easy to spot.....
0
votes
0
answers
23
views
Be first to answer!
Asked 10 months ago By Elgin
Category: General Questions
0
votes
0
answers
111
views
Be first to answer!
Asked 10 months ago By EUM
Category: General Questions
What impact on power consumption, equipment reliability and life does running a three phase air conditioner air handler on single phase power supply?
0
votes
0
answers
221
views
Be first to answer!
Asked 10 months ago By Anonymous User
Category: General Questions
0
votes
0
answers
4
views
Be first to answer!
Asked 10 months ago By Pat
Category: General Questions
0
votes
0
answers
45
views
Be first to answer!
Asked 10 months ago By pb
Category: General Questions
can you over tonnage an ac unit? 2.5 to 3.5
0
votes
0
answers
5
views
Be first to answer!
Asked 10 months ago By Pat
Category: General Questions
0
votes
0
answers
12
views
Be first to answer!
Asked 10 months ago By jim
Category: General Questions
I have a big electric motor with a 6 groove sheave.  I have 2 v-belts each with 3 grooves.  Circumference of the belt is ~ 50'. Generic question is that if they are aligned proplerly, tensioned properly, and assumed to be same length, will the belts ...
0
votes
0
answers
21
views
Be first to answer!
Asked 10 months ago By Jason Souliere
Category: General Questions
Should mention how poor some of these decorative vents and registers can perform. They look pretty but tend to impede air flow as I have found in my own system. I have actually removed one of the dampers from every register in the house so they're al...
0
votes
0
answers
3
views
Be first to answer!
Asked 10 months ago By Amnon
Category: General Questions
I had 2 companies come and give me a quote for adding AC to my home that already has a furnace and ducts. One of them measured the static pressure. The total of the two measurements was about 0.75 (under furnace was 0.32 and above was 0.43). He said...
0
votes
0
answers
113
views
Be first to answer!
Asked 10 months ago By Anonymous User
Category: General Questions
Can you please provide me specifications on your model MB-GP1TA-D00B?  Thanks,  Adam
0
votes
0
answers
12
views
Be first to answer!
Asked 10 months ago By jayakarthick
Category: General Questions
Other than the clearly oversaw chart, the CNC unit offers a daze secured strengthen with pictures that demand shockingly clear programming.Unmistakably, this space is bound with various sorts of windings. For example, sectional and trapezoidal windin...
0
votes
0
answers
20
views
Be first to answer!
Asked 10 months ago By Chris
Category: General Questions
Ntc6075fba2 I want to know how many tons is it and if it can be converted to a r410  with a Goodman 4 ton 410
0
votes
0
answers
4
views
Be first to answer!
Asked 10 months ago By MARY
Category: General Questions

Ask A Question

Attach YouTube/Vimeo clip putting the URL in brackets: [https://youtu.be/Zkdf3kaso]