HVAC Controls (16)

No Registration Required To Ask & Answer Questions! Features Such As Voting or Marking Favorites Cannot Be Accessed Without Registration! All Questions & Answers Are Subject To A Small Delay In Posting Due To Moderation!
Votes
Answers
Views
Question
0
votes
0
answers
11
views
Asked 7 months ago By jayakarthick
Category: HVAC Controls
The XFLUX is associated for close nothing and direct level of inductors and spreads. The submersion level is high in the obliging application while inductance has savage stacked in UPS and power figure interface with secure.Magnet Wire
0
votes
0
answers
49
views
Asked 7 months ago By RONNY
Category: HVAC Controls
0
votes
0
answers
43
views
Asked 7 months ago By Airflow
Category: HVAC Controls
0
votes
0
answers
69
views
Asked 7 months ago By Airflow
Category: HVAC Controls
How do you resolve static air pressure problem
0
votes
0
answers
24
views
Asked 7 months ago By velmani
Category: HVAC Controls
How to calculate static pressure for AHU and Exhaust fans.. plz explain briefly.
0
votes
0
answers
4
views
Asked 7 months ago By MARY
Category: HVAC Controls
0
votes
0
answers
17
views
Asked 7 months ago By becky
Category: HVAC Controls
My doctor's office is on the 2d floor of a 3-story building.  The air conditioning on the 2d floor has been out for 2 summers now while the 1st floor is cool and even cold.  The hospital administrators claim the problem is with the "drive," which the...
0
votes
0
answers
15
views
Asked 7 months ago By taher
Category: HVAC Controls
we have a hall of 75.9m2 area. where we will divide it with 8 offices, probably with gypsum wall partitions. Now the thing is that we have installed 8 ducted split unit of 5TR each. the total tonage will be 36.5 now the area also needs one fresh air ...
0
votes
0
answers
11
views
Asked 7 months ago By naresh
Category: HVAC Controls
how can yo say filters become more efficient , when loaded with more and more partical
0
votes
0
answers
31
views
Asked 7 months ago By Abdullah
Category: HVAC Controls
how is static pressure generated? Like in the intake of ID fan there is a static Pressure. It can be measured by using manometers. But how this pressure is reached? What are the steps taken to achieve such static Pressure?
0
votes
1
answer
80
views
Asked 2 years ago By Billy
Updated 2 years ago By
Category: HVAC Controls
0
votes
0
answers
58
views
Asked 2 years ago By DannyBoy
Category: HVAC Controls
Stage1 - ECM  Motor - just Not getting below 1265CFM -4ton so No Cool Coil Stage 1 Just Blows  Humidity Straight Back Up to 64% from 54% Also the Stat Why is It all Locked Down to Max of 9 Min.  Stage 1 - After the House is Cool and Coil is Cold - Ho...
0
votes
1
answer
299
views
Asked 4 years ago By Frank
Updated 4 years ago By
Category: HVAC Controls
I have a Jade Controller installed with Y1 as economizer, and Y2 mechanical (conv). I have economizer, and 24 volts going to Y2 in, and nothing on Y2 out. I waited 10 minutes and still no signal.  I was told stage 3 had to be changed to 0, I did that...
0
votes
1
answer
364
views
Asked 4 years ago By Fern
Updated 4 years ago By
Category: HVAC Controls
When trying to properly charge a package unit using dry bulb and wet bulb readings, where do I get my wet bulb reading? At  the return side or supply side of the RTU?

Ask A Question

Attach YouTube/Vimeo clip putting the URL in brackets: [https://youtu.be/Zkdf3kaso]